Poseidon Cyklon HP Port Adapter

On older Poseidon Cyklon 1st stage SCUBA regulators, the standard thread size of all ports were 1/8. Today, all LP ports are 3/8 and all HP ports are 7/16 sized.

If you have an older style 1st stage, this adapter can be used to attach a standard High Pressure Hose.

• Male end: 1/8"
• Female end: 7/16"
• Includes new gasket

AGA FFM CONVERSION KIT, POS TO NON POS

Convert your Interspiro AGA Full Face Mask from Positive Pressure to Non-Positive Pressure. A common mis-conception is that Public Safety Divers want to go with the positive pressure FFM. They do this to keep contaminated water out of the mask and off the diver's face, but in reality the positive pressure FFM just complicates things by spraying water in the divers face when the mask is being put on or taken off (on the surface). If the positive pressure AGA is inverted it will let water in. In reality all FFMs have positive pressure, however the Pos Press AGA (originally designed for firemen) has a greater positive pressure than other full face masks or the AGA non-positive pressure version.

* Conversions should be done by Authorized AGA Service Technicians only.

The SEASOFT PRO / M6™ 6 mm Drysuit Hood is designed to be worn with a full face mask. It has a skin-in seal facing the diver's face AND a skin seal facing out toward the mask with a layer of tough nylon fabric sandwiched in between the two.

The three back panels are compressed neoprene for thermal protection so that your hood is NOT getting thinner as you are getting deeper.

SEASOFT uses 4 different types of neoprene to make these hoods.

The SEASOFT PRO / M6™ 6 mm Drysuit Hood is the best commercial diving hood available anywhere.

Why should you buy this SEASOFT PRO / M6™ 6 mm Drysuit Hood?

The SEASOFT PRO / M6™ 6 mm Drysuit Hood is our commercial drysuit hood designed to be worn with a full face mask. The PRO / M6™ has a layer of skin on the inside and on the outside with a layer of tough nylon in between these two layers. The skin allows the hood to seal to your face and the full face mask to seal to the hood.

Of course, the three back panels are of compressed neoprene to provide you with thermal protection as you descend. You don't want your hood getting thinner as the water is getting colder.

There are no seams down the middle of the chin, this prevents jaw fatique.

There are two layers of Titanium Flake Foil™ for added heat retention.
At the top of the hood there are two small holes with a built in baffle system inside the hood to purge excess air from inside your hood while preventing any cold water from entering.
The SEASOFT PRO / M6™ 6 mm Drysuit Hood is the perfect commercial hood for that specific dive.

Click Here for Full Face Masks

Interspiro AGA Nose Push Pad 3- Slot (Pre-cut)

• Original Pressure Equalizing Pad (Old Style) for the Inter)spiro AGA Full Face Mask.
• Easy replacement part for worn out or lost push pads.
• 3 - Slot
• Made in the EU.

AGA Push Pad (Nose Block) 

NRS Tow Tether

The strong NRS Tow Tether, with built-in bungee, is used with the quick-release harnesses on rescue life jackets.

• Tow Tether lengths:
  33": Stretched length is 33", unstretched is 19"
  53": Stretched length is 53", unstretched is 33"
  Add 6" to length for carabiner and metal O-ring
• The Tow Tether, sometimes called a "cow tail," enhances towing boats in rescue situations.
• The stainless steel O-ring includes a hook patch of "hook and loop" material that facilitates centering of the O-ring on vests that have the loop material sewn on in the back.
• The Tether also has a hook patch on the carabiner end. This mates with a loop piece available on some rescue PFDs, forming a quick-release holder for the carabiner.
• The Standard D Locking Carabiner prevents accidental snag on brush in the field or with other gear.

Poseidon Cyklon Port Adapter

On older Cyklon 1st stages, the standard thread size of all ports were 1/8. Today, all LP ports are 3/8 and all HP ports are 7/16 sized.

If you have an older style 1st stage, this adaptor can be used to attach a standard Low Pressure Hose.

• Male end: 1/8"
• Female end: 3/8"
• pn: 0000-833 / 2415
• Do not use o-rings for seal. Use Cyklon gaskets which can be ordered here :
  Cyklon Port Gaskets

Si Tech Seamless PVC Gloves with Bottleneck Seals & Liner

A seamless glove made of PVC and latex, with a bottleneck seal. A durable and cost effective Dry Glove. Easy to use. These gloves make diving both comfortable and warm, and therefore makes it possible to keep the dexterity in the hands much better. These gloves comes with a separate acrylic liner which provides warmth and comfort to your hands.

*The Si Tech Glove is our replacement for the Nordic Blue Glove

Features:

• Seamless
• PVC and latex, fully coated
  
• Rough finish over entire surface
  
• Antibacterial and anti-odor treatment
  
• Special hydrocarbon treatment
  
• Anatomical shape
  
• Separate acrylic liner included for warmth and comfort.
• Bottleneck latex seal
• Three sizes: Medium, Large and X-large
  

Benefits:

• A flexible, soft glove, for ultra comfortable extended wear.
  
• Protect hands against chemicals.
  
• Remains flexible up to -20 deg Celsius / -4 deg Fahrenheit.
  
• Impermeable for working in damp or greasy environments, enabling you to grip objects easily.
  
• Surface provides tactile feel and better grip.
  
• Greater hygiene.
  
• Effective cold protection, with easy cleaning liner.
  
• Designed for easy movement and continuous wear.

AQUA LUNG RAPID DIVER PRO

The RAPID DIVER PRO is a lightweight, all-inclusive Scuba system that integrates a tank, regulator and buoyancy control module to a uniform-fit, load-bearing harness. It was created in response to public safety requests for a universal fit, compact, versatile and easily deployed Scuba system.

•Rapid front mount design
•Simple, quick, and convenient to use
•Self-adjustable with easy donning and doffing
•Aqua Lung Titan LX regulators
•2 tank configurations: horizontal front or vertical back mount
•Dual bag construction with up to 50 lbs of lift
•1050 D ballistic nylon fabric
•MOLLE cross webbing
•Integrated LP inflater with remote exhaust
•3 rapid pull exhaust dump valves
•Up to 50 lbs of lift
•27 CF steel primary tank
•2640 PSI low pressure
•Pre-sewn badge attachment
•Single carry case - ready to dive
•Soft carry case stores easily in trunk
•Supplied with black Aqua Lung Micro mask
•Supplied with paramedic shears in nylon sheath

Si Tech Shell Drysuit Inflation Valve

The Shell Inflation Valve is a high performance valve suitable for all areas of recreational and technical diving. The design of the housing makes it easy to locate and ables the diver to inflate a smooth flow of gas and fully control the buoyancy. The construction of the filter lid makes the Shell Inflation Valve suitable to use in conjunction with all common undergarments.

• Rotating “Push to Inflate” suit valve.
• International nipple.
• Raised (1/8”/3mm proud) or flush inflate button.
• Attaches to any current model of SI Tech valve port.
• Comes with #21007/8 Protective Cap.
• Anti friction washer included.
• # 25210

Aqua Lung Osprey Drysuit (Breathable Water Rescue Drysuit)

The Osprey is a long duration breathable water rescue drysuit designed for swiftwater, flood, and ice rescue missions. The unique design allows for a comfortable stand-by mode while still offering critical protection in unpredictable environments.

Features

• True self entry featuring Captive Zip Design (patent pending)
• Adjustable full circumference neoprene neckseal (patent pending)
• Saltwater resistant waterproof breathable material
• Fully donned or stand-by mode
• Anti-flush “wader belt” located under jacket
• Relief/comfort zipper
• Superior fit and comfort assisted by pre-shaped legs and torso
• Attached over jacket with dry zip protection
• Reinforced 420 denier nylon padded elbows,knees/shins, and seat
• Neoprene wrist seals with gauntlet overlays and hook and loop cinches
• Lower leg boot gauntlets with hook & loop cinches
• Attached soft dry socks
• Zippered chest pocket
• “Loop” shoulder panels for adhering patches
• High visible reflective patches, piping, and logos
• Picture shown with Evo boots (not included)

Material:

• Breathable/waterproof 3-layer material comprising:
• Durable 200 denier nylon, durable & water repellent
• Core - Breathable, non-porous, salt water resistant, polyurethane
• Inner layer - protective 18 denier nylon
• Neoprene wrist seals
• Adjustable circumference neoprene neckseal (patent pending)
• 420 denier nylon reinforced elbows, knees/shins, and seat

Color:
Red top/black bottom

Sizes:
S, M, MK, L, LK, XL, XLK, 2XL, 3XL, 4XL

Accessories:
Zipper lube and instruction manual. 

Size Chart / Click Here

 

 

 

 

 

 

 

 

 

 

Zeagle SAR BCD

Designed for the Search and Rescue Diver

The SAR BC, along with the 911 BC, was introduced in 1997 in response to many requests from Public Safety divers for systems designed to fit their needs. Identical to the 911, except for the addition of a permanently installed lifting harness for helicopter, cliff or swiftwater work.

Features:

• Integral lifting harness and saddle strap
• PFS sizing system
• Single or twin cylinder capability
• Two double pull waist buckles in front
• 1050 Denier Ballistic Nylon
• 65lb lift Ballistic bladder
• 36lb capacity Ripcord weight system
• 20lb capacity rear trim weight pockets
• Adjustable sternum strap
• Four Stainless Steel D-rings on shoulders, two adjustable
• 11" spaced grommets for mounting twin cylinders and metal backplates
• Two zippered utility pockets
• Full integral lumbar pad
• Six stainless steel D-rings on vest
• SOLAS reflective symbols on buckles
• Reflective 3M ScotchLite® trim on bladder
• Two hose storage pockets on the bladder
• Airloc buckles
• Articulated shoulder to reduce binding in the underarm and chest area as well as increase freedom of movement
• CUSTOM ITEM.....30 DAY LEAD TIME (min).

 

Vest Measure Waist Size		Shoulder Measure Shoulder to Waist
SM	28"-35"	SM	14"-18"
MD	33"-41"	MD	18"-22"
LG	37"-45"	LG	22"-26"
XL	42"-50"	XL	26"-29"
XXL	Custom	XXL	Custom

Si Tech Blue PVC Glove - Extended Cuff

A seamless glove made of PVC and latex, with a straight seal. Suitable for Dry Glove Systems where the glove is pulled over the ring. A durable and cost-effective Dry Glove. Easy to use. These gloves make diving both comfortable and warm, and therefore makes it possible to keep the dexterity in the hands much better. These gloves come with a separate acrylic liner which provides warmth and comfort to your hands.

Features:

• Seamless
• PVC and latex
• Separate acrylic liner included
• Straight latex seal
• Three sizes: Medium, Large and X-large
• PN: 60575

Poseidon Xstream Regulator 2nd Stage Exhaust Cover

Update or replace your worn out or faded Xstream 2nd Stage Regulator Exhaust Cover. Try a new color! All covers are the same, it does not make a difference what cover your regulator came with, now you get to choose the color. Some divers like to color coordinate, some Tech divers like certain colors to represent a specific blend of gas.

Poseidon Extreme OmniSwivel Version 2.0

Description: 

• OmniSwivel for Poseidon Extreme Stage Regulator
• 3 way 360deg rotation
• 9/16"-18 Male to Poseidon Extreme Female Insert
• Version 2.0 with a set screw that captures the spindle-screw and prevents it from ever being able to back out.

Details:

• Solid brass construction for maximum durability.
• Oxygen Compatible Materials and O-Rings.
• Viton 75 Orings with Tribolube 71 lubricant

Omni products are well known to the high tech divers and rescue workers that need total stability such as:

• Rebreather / Technical Divers
• Search, Rescue and Recovery Agencies
• Police Departments and Fire Departments
• Military
• NASA

Si Tech Argo Drysuit Exhaust Valve

SI TECH Drysuit Exhaust Valves are designed to make your dives pleasant and easy - avoiding dangerous pressure gradients between the suits inner and outer pressure with a maximum resistance of 25 mbar. The focus of the valves are the pressure precision that make SI TECH valves superior. This also prevents leakage of insulating gas when set to maximum pressure for extended surface buoyancy and warmth.

• Star Lid.
• Polyblend construction.
• Ratcheting action - you can feel and hear the adjustment.
• Variable volume control.
• Will fit any current model of valve port.
• High flow lid provides excellent exhaust gas flow.
• Anti-friction washer included.
• # 11335

Important information in regards to attachment of SI TECH Exhaust Valves
During the years we have received some Exhaust Valves that has taken damage by incorrect attachment procedures. The information in this section is intended to prevent this to happen. The most common way of damaging an Exhaust Valve during the attachment procedure is by holding the adjustment lid and using force to rotate it when tightening the valve to the Valve Port. Please always try to have SI TECH Attachment tools available when attaching the valve onto a drysuit. If you do not have Attachment tools, please follow the guide below.

Shearwater Perdix AI Dive Computer

Shearwater Perdix AI comes standard with no transmitter. During checkout please select no transmitter or Add Transmitter for $350.

Shearwater is proud to introduce the newest member of the Shearwater family: The Perdix AI. Offering all of the same great features of the Perdix, the Perdix AI uses its large, easy-to-read screen to clearly display the tank pressure as well as your gas time remaining (GTR). The Perdix AI is capable of connecting to either one or two transmitters giving the diver the option to monitor both tanks or dive sidemount.

The Perdix AI dive computer from Shearwater search, is a robust dive computer for technical divers of all levels, and ready out of the box for air, nitrox, and trimix gasses. The Perdix AI is the newest offering from Shearwater, similar in design an operation to the Petrel line of dive computers, but in a smaller form factor.

Its simple 2-button interface and easy to navigate menu structure allows for intuitive and quick operation underwater. The Perdix AI features a large, high resolution LCD screen is both easy to read, and power efficient. The Perdix AI operates on any AA sized battery, and is user-replaceable in the field with minimal effort. The included digital compass is both accurate and smooth, and Bluetooth integration offers download and upload capability from Mac, PC, and iOS devices.

The Perdix AI may be used for open-circuit and closed circuit-diving, as well as gauge mode if desired


The small form factor of the Perdix AI does not allow for an external connection for rebreather oxygen cell monitoring. Despite this, closed-circuit rebreather divers find the Perdix AI more than adequate for CCR decompression calculations using a manually entered PO2 setpoint.

In closed-circuit mode, the Perdix AI stores banks of 5 closed-circuit diluent gasses, as well as 5 open-circuit bailout gasses. In open circuit mode, 5 bottom mixes, and 5 decompression gasses may be stored. Gas switching is performed quickly and easily with minimal button pushes. Gasses may be added or edited while underwater – useful for lost gas scenarios.

Decompression Algorithm

The Shearwater Perdix dive computer features the following modes of operation:

OC Rec - 3 gas nitrox recreational computer
OC Tec - Multi gas, trimix decompression computer
CC INT - Closed circuit fixed PPO2
Gauge - Bottom timer with stopwatch and dive logging

All Shearwater dive computers use Buhlmann ZHL-16C as the decompression algorithm. User adjustable conservatism may be achieved by manipulation of gradient factors settings in the computer’s settings. An optional VPM-B algorithm may be purchased if desired, and installed in the field.

The 2.2" Color LCD display is easy to read, with high contrast, and automatic screen brightness. The display may be customized with user-defined font colors, and may be inverted for those who wish to wear the Perdix AI on their opposite arm. Several layouts may be selected from, and fonts may be customized for size and color.


The user interface is simple to use with adaptive menus. Commands are entered with piezoelectric buttons. Warnings are clear and concise using color-coded fonts. A simple 2-button bailout allows for quick and easy changes to open-circuit. No confusing icons are used; rather the Perdix AI navigation is done with plain-language. Divers have a choice of metric, or imperial units.


The Perdix AI operates with any AA-sized battery. Shearwater Research recommends the use of Duracell Coppertop alkaline batteries for their widespread availability, and reliability. Shearwater dive computers will operate about 30 hours on a quality alkaline battery, or up to 95 hours using Saft LS14500 batteries. Li-Ion, NiMH, Photo Lithium 1.5 and Zinc-Carbon 1.5 batteries may also be used.

The Shearwater dive computers also features a super-capacitor to keep track of your tissue loading in the event a battery change is required between dives. This capacitor holds enough energy to maintain tissue status for 15 minutes. This means that if your battery change takes less than 15 minutes you can continue with repetitive dives, and don’t have to reset the date and time.

The Shearwater Perdix AI features a 1000-hour dive log, which may be downloaded via Bluetooth to a Mac, PC or iOS device using free Shearwater Desktop. The Bluetooth feature may also be used to upload firmware updates, when available. 

OxyCheq Deluxe Adjustable Harness Chroma Series- Safety Orange w/ Reflective

Miflex 2 Xtreme High Performance Specialist Diving Regulator Hoses

• Extreme Abrasion Resistance
• MIFLEX hoses feature an external nylon safety braiding designed to outperform and outlive traditional rubber hose
• Patent-pending MIFLEX double braiding design
• Polyurethane compound liner
• Polyester inner layer with nylon outer layer braiding
• Fittings and sleeves of UNI EN12164 CW 614N chrome plated brass
• MIFLEX braided hoses are tightly bound and fixed to the hose core by brass sleeves
• Double braiding also resists UV rays out of the water, extending the life span of the hose
• Oxygen cleaned and tested at the factory
• Lightweight and Flexible
• More than 30% lighter in weight when compared to rubber hoses of the same length
• Kink-resistant design
• Tie an MIFLEX hose into a tight knot and the flow of air remains continuous through the hose

The Xtreme high performance range of diving hoses has been developed in cooperation with expert divers for a superior in depth performance. A team of Miflex 2 engineers analyzed the low point of traditional low pressure diving hoses. The fruit of their research is the Xtreme high performance range. Xtreme hoses feature an external nylon safety braiding designed to resist the snags and abrasions that divers often encounter. The patent-pending Xtreme double braiding also resists UV rays out of the water, thus extending the life span of the hoses. Unlike the traditional hoses, the Xtreme nylon safety braiding is not simply pushed over the hose fittings. Instead the braiding is tightly bound and fixed to the hose core by stainless steel or brass sleeves. The result? Performance and durability in extreme situations. Tie the Xtreme hose in a tight knot and the flow of air remains continuous through the hose. Now that’s versatility! The Xtreme also achieves a higher burst pressure – more than double when compared to most traditional hoses. And in the event of a physical breach, Xtreme hoses actually work to reduce the amount of air lost. How? The advance Xtreme nylon safety braiding actively shrinks under pressure, reducing the rate of air loss and buying valuable time. Xtreme hose production is carried out on automatic assembly and testing lines designed and manufactured exclusively by Miflex. Each and every Xtreme hose is subjected to more than 30 individual safety and specification checks. Any hose found not to meet the exact Miflex standard is immediately scrapped.

Inspection and Use of Miflex Xtreme LP diving hoses
Miflex Xtreme LP diving hoses are high performance hoses which are lighter and more flexible than traditional diving hoses. Just like carbon fibre has advantages over steel, carbon fibre performs differently and must be cared for and used differently than steel. Likewise, careful use and inspection is critical to the safe use of your Miflex Xtreme LP diving hose.

While in storage, or during transport of your hoses to or from storage, your hoses could become damaged in a number of ways. Never use your hose as a carrying or hanging handle for the tank. Before every dive, carefully inspect your hoses for damage, wear and tear. Pay particular attention to the area near the fittings. If your hoses show any sign of wear, no matter how slight, immediately replace the hose.
During a dive, and unknown to you, your hoses could be caught on sharp rocks, twisted or subjected to other stresses. After every dive, carefully inspect your hoses for damage, wear and tear. Pay particular attention to the area near the fittings.
Never leave your hoses dangling with any regulator installed, especially when they are without pressure. Always secure the hoses to your jacket with hooks or straps, but leave sufficient freedom for movement. These hooks or straps should be fixed directly to the regulator, or close to the hose fittings. Never secure your hose in a manner which could constantly flex or bend in the same location (i.e. create a “hinge effect”). Continuous bending at the same pivot point will shorten the life of your hose.
Never over-flex your hose. Never fold the hose back onto itself. If your hose is too long, you may loop it and secure it in place with a section of rubber tubing (such as the inner tube of a bicycle tire). However, the minimum bending radius must be at least 3.5 times the outer diameter of the hose. For example, if the outer diameter of your hose is 12mm, then the minimum bending radius (as measured to the inside of the hose) is 42 mm. Never allow the weight of your air tank to impact or rest on any part of your hose. To prevent personal injury and damage, install the low pressure hose ONLY into a low pressure outlet of the first stage regulator

Inspection Tips

• Miflex hoses are manufactured to the highest standard in excess of the EN250 requirements. The Miflex brand is laser printed on all hoses to ensure recognition of the Quality of our products. Miflex hoses are quality guaranteed and each hose is 100% tested. All materials are RoHS approved with no hazardous substances used in our manufacturing process.
• Guaranteed with our commitment to maintaining exceptional quality.
• If there is scuffing on the outer layer of the hose, especially when used in cave diving type situations, where the hose could rub against sharp or uneven surfaces, replace the hose.
• If there are more than six loose threads in the same area on the outer layer of the hose, replace your hose.
• If there is any damage or excessive scale build-up on the hose fittings, replace your hose.
• Never cut your Miflex hose and reconnect any type of fitting to the hose. The hose will suddenly and unexpectedly fail at the fitting.

Low Pressure Inflator hose for BCD or Drysuit

• Easy See & Grip Wide Collar
• Easier Attachment
• Easier Removal
• Flattened Side to Prevent Clearance Issues
• Standard Shrader Valve Style
• Standard Collar Attachment
• High Quality Rubber

• WP: 400 psi
• BP: 2000 psi
• 3/8 - 24 UNF Male to Standard BC
  Quick-Disconnect Female

S.S. NAUTIC COBRA

AustriAlpin is pleased to introduce our newest addition to the Cobra fleet. Made of premium quality, A4 INOX Stainless Steel, the new S.S. Nautic is designed for ultimate safety performance in the most severe oxidizing environments. Ideal for applications like Offshore rigging, Navy, Coast Guard, SCUBA, Marine hardware, Bosun supplies, Yahting, and whatever or wherever else nature demands the ultimate in performance. Patent Protected.

• 18kN load bearing
• 1.75" webbing compatible
• Lightweight design
• Stainless Steel

AustriAlpin is premium quality PPE safety hardware. Whether it be for military, industrial safety, fall stop, para-sport, SAR, fire/polic/tactical, theatrical rigging, or climbing and mountaineering - you just won't find higher quality, performance or safer products anywhere in the world. You'll also be pleased to know that we don't outsource our production to cheap labour based manufacters in Asia - where quality and consistency go to die. You can trust our hardware to be the safest and most enduringly consistent in the world.

Patented AustriAlpin COBRA™ quick releases are, without equal, the safest, most finely crafted, and strongest load bearing buckles available anywhere. They are also the only stab-lock style fastener in the safety products market that will not open while under load. That makes them the best choice (we believe, the only choice) for ensuring the highest degree of safety for yourself or your customer. COBRAs are CNC machined, assembled, inspected, and packed (re: from alpha to omega) in our ISO quality assurance acredited facility. All COBRA products are tested and certified by highly respected independent /3rd party test houses and exceed Mil Spec guidelines for dust / sand / salt water as well as all applicable CE, EN, CSA, ANSI, and NFPA standards for fall-protection and personal safety. Our superior designs and commitment to quality guarantees the highest degree of reliability and assurances for safety and strength. Not too mention, they look awesome too!

BARE Semi Dry Snorkel

• Streamlined oval-shaped bore
• Splash-proof dry guard virtually eliminates water intake
• Quick release buckle detaches with single-handed action
• Easy purge system with extra large self draining chamber
• Angled mouthpiece holder on lower housing
• Clear and black silicone available (black silicone only available with red colorway)

Colors:
Translucent Blue, Black, Neon Yellow, Clear, Red

BARE Fastback Full Foot Snorkeling Fins

Soft rubber foot pocket, Thermo-plastic blade with flex panel for improved thrust, Reinforced side rails stiffen blade and control lateral spillage. Excellent travel fin for snorkeling or scuba diving.
*Please call for availability.

ZEAGLE CODE 3 FOR RAPID EMERGENCY RESPONSE

U.S. Water Rescue presents the Zeagle Code 3 Rapid Diver. Code 3 Rapid Diver is the next generation of BCDs for all military, coast guard, law enforcement, maritime, security, marine patrol and fire and rescue personnel. It’s a convenient diving system that’s designed specifically for rapid response to an emergency. Featuring an enhanced MOLLE strap system with additional strap areas for accessories; dual tank mounting bands that secure the tank vertically, horizontally, and large reinforced padding adds comfort. Reflective tape increases visibility and makes the diver easily identifiable.

• 2 Tank configurations (horizontal and vertical back mount)
• 20 cu ft Tank
• 5000psi Gauge with Miflex Hose
• Additional MOLLE Strap areas for accessories
• Reflective Tape for easy identifying in all environments
• Durable 1680D Ballistic Nylon
• 2 OPV Pull Dumps
• Adjustable Waist and Crotch Strap
• Razor Regulator System
• USWR Approved

Si Tech Quick Glove Set

A user friendly and versatile SQUEEZES-ON system for drysuit gloves:

• Donning and doffing your gloves can be done without assistance
• Don by squeezing. Doff by turning the Release Ring with one hand
• Use different gloves depending on the diving conditions
• Fits almost any dry glove

Quick Glove Rings – glove adapter, combines with these docking systems:

• Quick Clamp – docking for latex seals fixed to the suit
• Quick Cuff – cuff seal exchange system (factory-fitted by some suit brands)
• Quick Glove Docking Rings for rubber cuff rings – Mainly for commercial suits with fixed rubber cuff ring

Quick Glove Rings Kit Include the following:

• Connecting Ring (between glove and docking surface) 2 PCS
• Release Ring 2 PCS
• O-Rings (+ spare O-Rings) 2 PCS
• Spanner Ring Black – for thick gloves 2 PCS
• Spanner Ring Blue – for thin gloves 2 PCS
• Pressure Equalization Tube 2 PCS
• Paraffin wax (for friction reduction)
• Manual
• pn 60230

*Gloves not included.

Poseidon Cyklon Regulator LP Hose

Poseidon Cyklon LP Hose. Used for connecting 2nd stage Poseidon Cyklon regulator to 1st stage Cyklon. If you have an early model Cyklon 2nd stage, you might find that the threads on the LP hose may no fit a newer model Cyklon. In which case you will either need an adapter or this new LP Hose with the updated threads.

Not only unique in style, durability, reliability and longevity, the Cyklon is also unique in the type of hose used to connect to the 2nd Stage.  This hose LP UNF 3/8 Hose is used to connect the Cyklon Second Stage regulator to its First Stage.  The connection point between the Cyklon Second Stage and the hose is of a unique design and is not the same as most conventional Second stage regulators currently manufactured, so this hose is not appropriate for non-cyklon regulators.

*An adapter (0000-833) would be needed to use this hose on older First Stages that have G 1/8 port threads.

Key Features:

• Hose is for Cyklon 2nd stage only
• Multiples sizes available.

NRS HydroSkin Wetsocks

Description Protect your feet and keep them warm without the bulk of other wetsocks. NRS HydroSkin® Socks are the ultimate wetshoe liner. And, hey, they work great with sandals too.

• The 0.5-mm neoprene core insulates and protect.
• 4-way-stretch PowerSpan™ outer layer gives you enhanced mobility and greater durability.
• The ThermalPlush™ inner lining increases insulation, repels moisture and dries quickly.
• Titanium laminate adhesive aids body heat retention without adding bulk.
• DWR coating forces water to "bead" and roll off the material, reduces evaporative cooling.

Technical Specs

• Material: 0.5-mm Terraprene™ neoprene
• HydroSkin Material::
  • 4-way stretch PowerSpan outer layer
  • ThermalPlush™ inner lining
  • Titanium laminate adhesive
  • DWR coating
• Seams: Flat-lock stitched
• Taped Seams: No

Halcyon Infinity BCD

The Halcyon Infinity is not your typical buoyancy compensator. In fact, it establishes a new standard in single-tank diving, offering the unparalleled performance of a back mounted harness and the easy adjustability of a jacket BC. The heart of the Infinity BC is Halcyon’s Cinch Quick-adjust harness (patent pending). The Cinch harness is also available for double tanks and as an upgrade to existing Halcyon diving systems.

The Cinch Quick-adjust provides rapid adjustment of the diving harness, allowing an unprecedented fit and easy equipment removal. The Infinity also features Halcyon’s new deluxe Harness Pads, providing the ultimate in diving comfort and convenience.

The Infinity BC features Halcyon’s immensely popular Eclipse wing; the long, narrow profile supports a diver’s tank along his or her entire length, preventing unnecessary drag and minimizing in-water effort.

Key Components of the Infinity BC System

• Cinch Quick-adjust infinitely adjustable with a simple push or pull of the webbing
• Eclipse Buoyancy Compensator (wing); available in either 30- or 40-lb. (14- or 18-kg) lift capacity
• Choice of Aluminum or Stainless Steel Backplate; standard or small size
• ACB10 weight pockets
• Halcyon Deluxe Harness Pads featuring a Storage Pak for convenient stowage of lift devices
• Stainless steel Single-Tank Adapter (STA) with two cam straps; accommodates a weighted 6 lb insert
• Secure, continuous webbing provides a custom fit; eliminates unwanted tank movement
• Pre-bent shoulder D-rings facilitate quick storage of accessories from Scout lights to stage bottles
• Complete adjustability of D-rings eliminates inappropriate attachment points.
• EPDM elastic bands help secure accessories
• SS waist buckle
• Adjustable crotch strap enhances stability, nearly eliminating unwanted tank movement.

BACKPLATE:
As with most Halcyon products, an immense amount of behind-the-scenes work is required to create a plate we are proud to sell. Halcyon backplates have been refined over the years to provide the highest-quality finish and materials available. Small details like the unique bends near the bottom of the plate create an ergonomic curve, increasing diver comfort. Meanwhile our precise fabrication process ensures the quality you have come to expect from Halcyon. Each Halcyon backplate is cut from the highest quality stainless steel and sophisticated CNC machines mill every edge; this detailed process eliminates the sharp edges common with competitors’ plates. Machine polishing is augmented by individual handwork, perfecting both form and function.

• Constructed from high-grade, polished Stainless Steel or hard-coat Aluminum
• Carefully milled surfaces eliminate sharp edges
• Available in two sizes, both are compatible with any Halcyon BC component
• Standard: 6-lb. (2.7kg) Stainless Steel or lighter weight 2-lb. (.9kg) Aluminum
• Standard-size plates are 15.5” X 10.25” (39.3cm x 26cm)
• Small: 5-lb. (2.26kg) Stainless Steel or 1.8 lb. Aluminum
• Small plate measure 14” x 9.25” (35.5 cm x 23.5cm)
• Utility holes allow mating with Storage Pak to stow a variety of lift devices as well as the small Halcyon dry suit inflation kit

The Halcyon backplate pocket is the most efficient means to store any of the various Halcyon inflatable markers with ease. Stowing your favorite lift device in a Halcyon Storage Pak provides a hassle-free storage place without compromising the ability for rapid deployment. The Pak bolts directly onto your backplate and the downward-facing pocket can even be used to stow the 6-ft. long Diver’s Life Raft.

Click here for VIDEO

*Please call us for help in deciding which wing / plate is best for you

Halcyon CINCH Quick-Adjust Harness Upgrade

Key Components of the Cinch Quick-adjust Harness

• Cinch Quick-adjust harness; infinite adjustability with a simple push or pull of the webbing
• Available in Standard and Small sizes to fit our stainless steel or aluminum Halcyon Backplates
• Can be used with single or double tank BC Systems
• Seamless use with Halcyon ACB weight pockets, canister light, and hip D-ring

Components include:

• Cinch Adapter Plate (Patent pending)
• 12' of replacement H Webbing
• ACB Weight Pocket Adapters
• D-ring Assembly
• Light Retainer Assembly
• SS Bolt Kit
• Quick-adjust Crotch Strap
• Double tank Bolt Extender