


38 products
Si Tech Quick Glove Rings
60230
Regular price $97.50 Save $-97.50A user friendly and versatile SQUEEZES-ON system for drysuit gloves:
Drysuit Latex Hood
Regular price $100.00 Save $-100.00
Adding or replacing a latex hood to your drysuit offers better protection in contaminated water. It also provides added warmth in cold water (as long as you wear some time of knit hat (polar tech, etc) underneath the latex hood.
Drysuit ProTalc
TM-Talc
Regular price $5.99 Save $-5.99SILICONE WRIST SEALS
S61025
Regular price $56.00 Save $-56.00Silicone Wrist Seals are constructed from hypoallergenicic silicone that have 40 % better stretch and offer enhanced comfort compared to latex seals. Divers with latex allergies can dive carefree, knowing that the seals are non-allergenic. The seals are durable and resistant to degradation by UV light, ozone or chemicals. The elasticity makes donning the suit much easier and it seals with your skin more effectively. Since the pressure is lower on the wrists your hands will stay warmer.
TECHNICAL SPECIFICATIONS:
Si Tech Shell Drysuit Inflation Valve
S25210
Regular price $91.65 Save $-91.65Si Tech Valve Attachment Tool (pair)
S18222
Regular price $37.05 Save $-37.05Valve Attachment Tools are recommended to enhance the grip when detaching and/or re-attaching SI TECH valves and Blanking plug.
Si Tech Star Lid Argo Exhaust Valve
S11335
Regular price $95.55 Save $-95.55Important information in regards to attachment of SI TECH Exhaust Valves
During
the years we have received some Exhaust Valves that has taken damage by
incorrect attachment procedures. The information in this section is
intended to prevent this to happen. The most common way of damaging an
Exhaust Valve during the attachment procedure is by holding the
adjustment lid and using force to rotate it when tightening the valve to
the Valve Port. Please always try to have SI TECH Attachment tools available when attaching the valve onto a drysuit. If you do not have Attachment tools, please follow the guide below.
The red section of this illustration shows the rotatable adjustment lid. The green section shows the protection ring. The "black" bottom section of the valve is the attachment nut. When tightening the valve to the Valve Port, please follow these simple steps:
- Tightening of the valve is made by rotating the attachment nut on the inside of the drysuit together with the anti-friction washer and at the same time holding the protection ring, on the outside of the drysuit, in a firm grip.
- Do not hold the adjustment lid (marked red) when tightening the valve, this will damage the valve! Why? This is the rotatable adjustment part of the valve. If you by force rotate the adjutment lid beyond its end position you will either damage the lid itself or crucial internal parts of the valve.
SEASOFT PRO / M6 6mm Drysuit Hood for wearing with a full face mask
S-002-006x
Regular price $99.99 Save $-99.99The SEASOFT PRO / M6™ 6 mm Drysuit Hood is designed to be worn with a full face mask. It has a skin-in seal facing the diver's face AND a skin seal facing out toward the mask with a layer of tough nylon fabric sandwiched in between the two.
The three back panels are compressed neoprene for thermal protection so that your hood is NOT getting thinner as you are getting deeper.
SEASOFT uses 4 different types of neoprene to make these hoods.
The SEASOFT PRO / M6™ 6 mm Drysuit Hood is the best commercial diving hood available anywhere.
Why should you buy this SEASOFT PRO / M6™ 6 mm Drysuit Hood?
The SEASOFT PRO / M6™ 6 mm Drysuit Hood is our commercial drysuit hood designed to be worn with a full face mask. The PRO / M6™ has a layer of skin on the inside and on the outside with a layer of tough nylon in between these two layers. The skin allows the hood to seal to your face and the full face mask to seal to the hood.
Of course, the three back panels are of compressed neoprene to provide you with thermal protection as you descend. You don't want your hood getting thinner as the water is getting colder.
There are no seams down the middle of the chin, this prevents jaw fatique.
There are two layers of Titanium Flake Foil™ for added heat retention.
At
the top of the hood there are two small holes with a built in baffle
system inside the hood to purge excess air from inside your hood while
preventing any cold water from entering.
The SEASOFT PRO / M6™ 6 mm Drysuit Hood is the perfect commercial hood for that specific dive.
Catheters
OD-07-0001
Regular price $4.00 Save $-4.00Oxycheq P-Valve Balanced w/ QD
OD-04
Regular price $105.00 Save $-105.00Inflator Valve 360 Swivel w/ Cap
IB-inflator
Regular price $80.00 Save $-80.00Argon Drysuit Inflation System
HL413
Regular price $399.90 Save $-399.90Highland SS Pony Mount: For Aluminum 6 cu ft pony cylinders
HL412
Regular price $99.00 Save $-99.00Highland SS Pony Mount: Aluminum 8, 13, & 19 cu ft
HL409
Regular price $99.00 Save $-99.00EVO4 SCUBA Dive Boots
EVO4
Regular price $130.00 Save $-130.00McNett Dive Gear Essentials
DM-DCE
Regular price $24.99 Save $-24.99Drysuit Latex Neck Seal
Regular price $36.00 Save $-36.00
Trimmable Drysuit Latex Neck Seal. Don't get to the dive site and discover you have a torn neck seal. A torn or leaking neck seal can make for a miserable scuba diving experience or even worse NO Dive! Replace your old or worn out seal today with this high quality latex replacement.
Low Profile Automatic Dump Valve
DA-AP0704
Regular price $89.00 Save $-89.00Dry Suit Gaitor System - Unisex
B08897
Regular price $114.95 Save $-114.95The BARE Gaitor provides replaceable supplementary lower leg abrasion protection along with adjustable tension control to prevent excess air entering the boots.
Drysuit Glove with Liner
B-088947BLU
Regular price $57.99 Save $-57.99Latex Bottleneck Wrist Seal
B-088941
Regular price $31.95 Save $-31.95Repair your drysuit or perform some preventative maintenance with these premium, heavy duty Drysuit Wrist seals! Don't wait until your seals tear while gearing up for a dive.
To care for your drysuit seals: Apply a drysuit talc powder to the inside of the seal prior to donning the suit, do this everytime. At the end of the day, wash the inside and outside of the seals with clean water. Using a mild soap solution with warm water is best, but not an absolute necessity. Follow these simple drysuit seal care insturctions and you will extend the life of your drysuit wrist seals.
SEALTEK DRY HOOD
Regular price $49.00 Save $-49.00
Our highest performance hood that set the standard for comfort and sealing.
Travel Argon Mounting Kit 6 Cuft & 13 Cuft
AO-OTB-04-03
Regular price $39.00 Save $-39.00Argon Tank Aluminum 8
AL08RG
Regular price $189.00 Save $-189.00"EZ" QD Adapter (Low Pressure Quick Disconnect)
AC900
Regular price $20.00 Save $-20.00Dry Suit Hanger
AC510
Regular price $15.00 Save $-15.00Drysuit Polytex Wrist Seals with Adhesive
623XX
Regular price $59.00 Save $-59.00Drysuit Polytex Neck Seal w/ Dry Adhesive - Sized
62323
Regular price $69.95 Save $-69.95Trimmable Drysuit Polytex Neck Seal with Dry Adhesive. Don't get to the dive site and discover you have a torn neck seal. A torn or leaking neck seal can make for a miserable scuba diving experience or even worse NO Dive! Replace your old or worn out seal today with this high quality latex replacement.
What are Polytex Seals?
Whites Polytex seals are a combination of Vulcanized Natural Rubber Latex and Polyurethane. The Polyurethane stabilizes the Latex and helps inhibit the seal from tearing. Ever get a small tear in a seal and it runs the length when donning the Drysuit? Although not indestructible, Polytex reduces this tendency and allows for a repair to be made to the seal, not necessarily making a replacement mandatory. Additional anti-aging ingredients are added to combat the effects of ultra-violet light, ozone and copper. These additions make for a tougher, longer lasting seal when compared to standard latex seals.
Polytex neck and wrist drysuit seals come standard on the Whites (now Aqua Lung) Hazmat Drysuits.
*Please select Large or XL in Order Notes.