Interspiro AGA FFM  Omniswivel Version 2.0

Omni products are well known to the high tech divers and rescue workers that need total stability such as:

• Rebreather / Technical Divers
• Search, Rescue and Recovery Agencies
• Police Departments and Fire Departments
• Military
• NASA

Brass 2nd Stage Regulator Quick Disconnect - XS Scuba

• Add a quick-disconnect to most any regulator or full face mask
  

• Installs between low pressure regulator hose and second stage

• Lock-down screw to prevent accidental disconnection
  

• Chromed brass construction

• Low pressure use only - below 200 psi

• Factory cleaned - Viton o-ring

• Part # AC990

Standard OmniSwivel for use with the Guardian Full Face Mask

Description: 

• OmniSwivel for 2nd Stage Regulator
• 3 way 360deg rotation
• 9/16"-18 Male to 9/16"-18 Female Insert

Details:

• Solid brass construction for maximum durability.
• Oxygen Compatible Materials and O-Rings.
• Viton 75 Orings with Tribolube 71 lubricant

• Rebreather / Technical Divers
• Search, Rescue and Recovery Agencies
• Police Departments and Fire Departments
• Military
• NASA

The SEASOFT PRO / M6™ 6 mm Drysuit Hood is designed to be worn with a full face mask. It has a skin-in seal facing the diver's face AND a skin seal facing out toward the mask with a layer of tough nylon fabric sandwiched in between the two.

The three back panels are compressed neoprene for thermal protection so that your hood is NOT getting thinner as you are getting deeper.

SEASOFT uses 4 different types of neoprene to make these hoods.

The SEASOFT PRO / M6™ 6 mm Drysuit Hood is the best commercial diving hood available anywhere.

Why should you buy this SEASOFT PRO / M6™ 6 mm Drysuit Hood?

The SEASOFT PRO / M6™ 6 mm Drysuit Hood is our commercial drysuit hood designed to be worn with a full face mask. The PRO / M6™ has a layer of skin on the inside and on the outside with a layer of tough nylon in between these two layers. The skin allows the hood to seal to your face and the full face mask to seal to the hood.

Of course, the three back panels are of compressed neoprene to provide you with thermal protection as you descend. You don't want your hood getting thinner as the water is getting colder.

There are no seams down the middle of the chin, this prevents jaw fatique.

There are two layers of Titanium Flake Foil™ for added heat retention.
At the top of the hood there are two small holes with a built in baffle system inside the hood to purge excess air from inside your hood while preventing any cold water from entering.
The SEASOFT PRO / M6™ 6 mm Drysuit Hood is the perfect commercial hood for that specific dive.

Click Here for Full Face Masks

OmniSwivel High Pressure 1st Stage Pivot Swivel

This OmniSwivel pivot swivel is used for high pressure ports (pressure gauge). It allows your pressure gauge to swivel (instead of fixed) at the 1st stage connection.

• For High Pressure Hoses
• 7/16-20 Male to 7/16-20 Female.
• 90 degree angle, 360 degree rotation.
• Outer Dimensions: 2.3cm x 3cm

• Rebreather / Technical Divers
• Search, Rescue and Recovery Agencies
• Police Departments and Fire Departments
• Military
• NASA

HSA-2 Low Pressure Hose For AGA Mask

• Supply hose designed for the AGA Interspiro FFM (Full Face Mask)
• Low Pressure
• Length: 32"
• Part #: 604001-034

Stainless Steel 2nd Stage Regulator Hose Quick Disconnect

• Add a quick-disconnect to most any regulator or full face mask
  
• Installs between low pressure regulator hose and second stage
  
• Click & Lock to prevent accidental disconnection
  
• Stainless Steel construction
  
• Low pressure use only - below 200 psi
  
• Factory cleaned - Viton o-ring
  
• P/N AC992

Second Stage Hose QD - Male Only

• This is the male quick-disconnect of the AC990
  
• Put these on multiple second stage regulator for quick swaps
  
• Chromed brass construction
  
• Low pressure only - below 200 psi
  
• Factory cleaned - Viton o-ring
  
• P/N AC991

Eyewear Kit for OTS Guardian FFM

Eyewear Kit. Add your prescription lenses to wire frames in your OTS Guardian FFM. With the Guardian Full-Face Mask Eyewear Insert, enjoy a clear view underwater with securely mounted, custom engineered and field-tested prescription ready eye gear.

GFFM Accessory Rail Light System

Dive With Your Hands FREE!

The accessory rail system easily attaches to the Guardian full-face mask and makes it possible to mount various lights, cameras, and other devices to the sides of the mask. This version has the “Inodive LED Dive Light” mounted to the accessory slide. This light is rated at 1watt (80 Lumen), and will burn for approx..4 hours on 2 AA batteries. A double O-ring seal, and magnetic switch, help insure the watertight integrity of the light to 150 feet. Other devices can be attached to the accessory rail by adding additional “Universal Slides” (purchased separately). Cameras, lights, and other devices are then changed by simply sliding them on or off the rail. This quick-disconnect feature allows surface support to quickly exchange or replace devices as the mission dictates without removing the mask from the diver, or the diver from the water. Each Accessory Rail can accept 2 slides. Additional slides can be purchased separately. One rail may be used, or two may be mounted (one on each side). The attachment method does not interfere with commonly used surface breathing valves.

Attaching the rail system to the Guardian mask makes it possible for a diver to have both hands free to accomplish difficult tasks underwater.

No tools are used to attach the rail system to the mask. Two thumb screws are simply tightened by hand to secure the rail system to the mask. No modifications are needed, and the rail is easily removed for mask maintenance.

Once devices are mounted to the removable “Slides” they can be slid onto any other dive mask, or dive hat, that has an Accessory Rail mounted.

The rail system is not mass produced—each one is made and assembled individually, and manufactured using quality materials.

OTS Guardian Full Face Mask w/ ABV

• Removable 2nd stage for easy cleaning and storage(cannot be used w/o mask)
• Made of a one-piece, pliable silicone skirt combined with injection-molded,high-impact,glass-filled nylon frame and regulator housing
• Double face seal and slightly smaller/low volume oral nasal cavity to fit most faces
• Customizable nose block for equalization
• Air flow is directed up the visor face to eliminate fogging and through one-way valves in the oral nasal pocket to reduce CO2 retention
• Second stage comes off the right shoulder and uses a standard LP hose
• Communications port for easy installation of a Buddy Phone or ear/microphone assembly to connect to OTS’ Diver Communications Unit such as the Aquacom® SSB-2010 OTS
• Ambient Breathing Valve® (ABV®) allows the diver to breathe ambient air at surface, thus conserving scuba air
• Includes Mask Bag and 32” LP hose 

The patented ME-16R Hot Mic® evolved from many years of research and development to design a true noise canceling microphone that can withstand the harsh marine environment. Many off-the-shelf elements have been used in diving helmets and full face masks (ffm), but require some sort of protection. The protection usually compromises the quality defeating its use. The Hot Mic has proven itself time and time again on many movie sets and Search & Rescue operations. The sound quality produced using a Hot Mic is second to none.

How does it work? A special membrane is used on both sides of the diaphragm which allows air, but not water, to enter. This allows the microphone to cancel noise that is more then 1/4" away. Noise such as air, bubbles and breathing sounds are virtually eliminated. This is especially noticed when using a full-face mask with an oral-nasal cavity. We have been contracted many times to help produce TV and/or Motion Pictures when studio-quality sound is a must.

Can the microphone element be damaged? Yes, the microphone has its limitations. The membrane is designed to allow a user to take the mask off at the back of the boat while in the water. In the past, microphones being exposed to sea water had a short life. Also, when cleaning a ffm, water damaged the old style microphone elements, not so with a Hot Mic. However, the Hot Mic® element can only withstand a differential pressure of about 12'. This means if a diver takes off the ffm at the back of the boat and drops down to 15', the membrane will not be able to keep the water out and the microphone element will be damaged. In our tests, we made several dives to 35' and took off an AGA ffm with a Hot Mic. After putting it back on and clearing it, communications were fine. However, if you took the full face mask off at 35' and dropped down to 47', the membrane would be compromised. We also found if you expose the Hot Mic at any depth down to 130' and come up, no damage will occur.

Conclusion: The Hot Mic will give you the finest intelligibility available and last for months with little maintenance.

The ABV-1 Ambient Breathing Valve (910271-000) allows the user to breath ambient air on the surface. This helps conserve air while you wait for your dive buddy or while on the surface.

The valve is easy to use, simply turn the valve counterclockwise one turn. Outside air will pass through the one way valve. It clears the lens then enters the (2) one way valves into the oral nasal cavity. You exhale through the 2nd stage regulator. When ready to dive, close the valve and you are on the way.

• The ABV *-1 Ambient Breathing Valve allows the user to breathe ambient air at the surface, conserving your tank air. It is simple to use and its low profile keeps it out of the way.
• To use the device, while on the surface simply rotate the valve counterclockwise. The one way valve will open and allow air into the FFM
• The one way valve located on the inside of the FFM ensures that your exhaled air does not go back out the valve. Your exhaled air is sent out through the second stage regulator ensuring you do not get a Co2 "building" in the FFM.(build-up)
• The valve also is forced closed when diving. The over pressure in the FFM assures that. If you forget to close the valve before diving, the valve disc will help keep water out.
• When the valve is closed, it has a low profile.
• When the valve is closed, it has a low profile.
• The ABV*-1 is a must for all Search & Rescue Teams, Military Divers and Divers who spend a lot of the time in the water!
• Order one today - with FFM purchase: ABV*-1 (910271-001) or separately with the visor ABV-2 (910271-002) or send us your visor and we can install one (installation fee $25.00 + ABV*-1 valve)(Note: It is recommended that a Certified Interspiro Service Technician install the visor).

Aquacom SSB-2010, 4-channel transceiver (5 Watts Output Power)

Model: SSB-2010, Aquacom SSB 4-channel, voice menu, diver transceiver.

Can be used w/CDK-6.

The Aquacom® SSB-2010 transceiver is a 5 watt, multichannel single sideband underwater telephone designed with Professional Search & Rescue Teams in mind. The Aquacom® SSB-2010 can be configured to operate with virtually any style full face mask (FFM) or mouth mask. With the addition of a CDK-6 Surface Accessory Kit, the Aquacom® SSB-2010 is easily converted into a portable surface station.

Standard features are: Voice Operated Transmitter (VOX), Push-to-talk control (PTT), Squelch, 4 channels, Earphone volumes, Voice menu (the user can adjust the SSB-2010 underwater via the voice menu), removable transducer, and heavy duty design.

This affordable system is tough, powerful, and a must for any serious Search & Rescue Team!

Item# 900272-000

Public Safety Divers, Military, and Law Enforcement please contact us directly for Public Safety Pricing.

AGA FFM CONVERSION KIT, POS TO NON POS

Convert your Interspiro AGA Full Face Mask from Positive Pressure to Non-Positive Pressure. A common mis-conception is that Public Safety Divers want to go with the positive pressure FFM. They do this to keep contaminated water out of the mask and off the diver's face, but in reality the positive pressure FFM just complicates things by spraying water in the divers face when the mask is being put on or taken off (on the surface). If the positive pressure AGA is inverted it will let water in. In reality all FFMs have positive pressure, however the Pos Press AGA (originally designed for firemen) has a greater positive pressure than other full face masks or the AGA non-positive pressure version.

* Conversions should be done by Authorized AGA Service Technicians only.

Poseidon Atmosphere Full Face Mask w/ 1st Stage

Atmosphere: The full-face mask of choice for professional and cold water diving.

The perfectly ­fitting Atmosphere is the (FFM) full­face mask of choice for professional and cold water diving. Install communication equipment to talk with your buddy during dives. As an over pressure mask it also allows you to dive contaminated water without getting dirty water on your face.

• For optimum performance, the Atmosphere should be connected to an Xstream 1st stage.
• Highly effective defogging system
• Antidistortion visor
• Prepared for communication system

AGA Full Face Mask Frame (Item #13 only)

• Replacement frame for Interspiro AGA Full Face Mask.
• Color: Black
• Number: 13
• AGA Full Face Mask service should be completed only by a Certified AGA Mask Technician.

Interspiro Weight Kit

For filming they are great! They not only balance the full face mask but help keep out unwanted light from the sides. This is typically a problem when looking into a video camcorders view finder.

Does the ffm need to be balanced. This depends on the user. Most users are not in the water long enough to notice a difference. However, professional divers who spend hours underwater will notice a slight rise in the ffm. This after hours becomes uncomfortable. The weights solve the problem.

90 Degree Elbow for FFM

90 Degree Elbow. Allows diver to re-route Low Pressure regulator hose for better trim & comfort. Fits Guardian Full Face Mask (FFM) & all standard 2nd stage regulators.

• Male: 9/16 - 18 UNF - 2B Regulator or Other Adapter
• Female: 9/16 - 18 UNF -2A LP Hose or Other Adapter
• No International Orders

• The OTS designed FFM Mask Bag prolongs the life of your full face mask.
  
• A large net type vent on the top of the bag provides greater air circulation which aids drying.
  
• Properly stowing the mask upside down in the bag allows the water to drain away from the second stage regulator and through the bottom of the bag via a large nylon grommeted opening.
  
• The bag has a dry compartment on the backside perfect for storing a supply hose or other small accessories
  
• It also has two mesh storage pockets; one found on the front and secured with a zipper and the second inside secured with a small Velcro® tab.
  
• The bag is made out of 420D nylon with polypro webbing, corrosion resistant nylon hardware: d-rings, straphooks, grommets, triglide (on the strap) and zipper sliders.
  
• It uses closed cell foam padding and a comes with a shoulder strap and a rubberized shoulder pad.